Home - Products - Download & Technical Support - The Diagnostic Process of Foxwell Scanner
« Go Back

The Diagnostic Process of Foxwell Scanner

Photos

The Diagnostic Process of Foxwell Scanner

Description

1) VERIFY THE FAULT

A crucial and often overlooked step.
Intermittent and poor explanation of faults can, if your not being careful, lead you down the wrong path. When the vehicle arrives in your work bay.

Step 1) Read and record faults
Note the stored faults down on a piece of paper (or take a shot with your smart phone). This is because there are often fault codes stored in a vehicle from previous issues, like a flat battery, Also very often you will see CAN Bus related fault codes due to the sometimes frequent corruption of date by electical interference.

Step 2) Clear Fault Codes
Erase the stored fault codes form the vehicles ECU.

Step 3) Reset Fault Codes
Test drive or operate the vehicle until the fault reoccurs. Then compare reset fault codes with previously recorded faults.

Poor Fault Explanation
Imagine your customer (or wife) says “the car goes all juddery and the thingy light is on”. You go out to the car check the vehicle for fault codes and find a fault code for an air flow sensor, Tell the wife, order one and install it. Only to have the wife say “I thought you fixed it”. You drive the vehicle… Brake Shudder and the vehicle was full of fault codes from a flat battery 2 years ago.

Intermittent Faults
The “Worst Case Scenario” for the fault finding technician. To be able to fix a fault with 100 percent accuracy you need to be able to witness the fault to occur and confirm the fault with tests. Any thing else is effectively guess work. Having said that there is a safety aspect to be considered. If a customer presents a car with the symptom -intermittent loss of power- And you find a fault code for the -Acceleration Pedal Position Sensor-, but are unable to duplicate the fault in any condition. It is advised to recommend the customer that the unconfirmed replacement of the sensor and servicing of the wiring (check and clean connectors) be carried out (with the potential situation of the customer trying to accelerate across and intersection and have the vehicle lose power in front of a truck). Also advise the customer that as this is an unconfirmed diagnosis that there is potential for this not solve the issue, however unlikely.

Always check the battery voltage -Must be above 11.00 volts. Always check the all fuses and relays.

 

  • 2) DETERMINE RELATED FAULTS

    Identifying related symptoms can help piece the puzzle together, for example if a vehicle presents with the symptom “Cruise control not working” and you notice the brake lights are not working, you can draw a link between the component both systems share, The brake light switch.

     
     
  •  

    3) INTERROGATE DATA

    Have a look at the live data, in the scan tool graph the data and ensure that it is plausible. For example if you are looking at an ABS fault and all except one displays 10 kph and you have a fault code for the left hand front sensor, you can confidently proceed with testing.

     
     
  •  

    4) TEST COMPONENTS

    There is always the potential (and in most cases more likely) to be wiring faults, as opposed to component failures. When fault codes and data point to a fault component it is recommended the component be tested to (measure resistance, check power supply, voltage drop test) to ensure you can rule out wiring faults.

     
     
  •  

    5) REPAIR

    Replace the faulty component and or make wiring repairs.

     
     
  •  

    6) RETEST

    Operate the vehicle in conditions that would have caused the fault to occur.

    Check and clear all fault codes.


    Relation product:

    Foxwell NT510



     


Write a Review
* Rating:
    Please select rating stars.
* Your First & Last Name:
* Your E-Mail Address:
* Review Detail:
*Verification Code:
          No right? Get a new Verification Code
 
Tell us what you think about this item and share your opinions with other people. Please make sure your review focuses only on this item. All reviews are moderated and will be reviewed within two business days. Inappropriate reviews will not be posted.
After-sales questions and issues: Contact our Customer Service Department. (A customer representative will get back to you).
Please Sign In first if you want to later edit or manage reviews uploaded by yourself.
Bookmark It